Right here in the next paragraph you might get a bunch of wonderful facts all about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a tub isn't exactly rocket science, but it does call for solid plumbing, carpentry, and sometimes, tiling abilities. Changing an old tub with a brand-new one is also a moderately difficult task. If the old tub is easily easily accessible, the job can relocate easily; if you have to open up a wall surface to eliminate the old tub as well as position the brand-new tub, the task is a lot harder. In either situation, the job is within a home handyman's abilities, although you will certainly need a helper to leave the old tub and also embeded in the new one. Make sure you have qualified yourself for the work and also are comfortable trying it. Instead of hiring a professional to take control of a halfway-completed project, it is far better to think about using one before you start. Possibilities are you may need a professional plumber to make tube connections.
This article will assist you set up a new bathtub in your shower room if you have currently gotten a brand-new bathtub and also don't need to alter the setup of your previous water supply pipelines.
Your tools and also material list ought to consist of the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installation, after that the first thing you need to do is detach the water supply. After doing so, switch on the faucets to drain any type of water staying in the system. The procedure of eliminating the existing faucets can be rather bothersome because of the limited gain access to that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a towel ready for the staying water that will certainly come from the pipelines. When the supply pipelines have actually been removed, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old securing substance.
Before proceeding to fit the brand-new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin making sure that the washers are in location between the tap as well as the sink. Safeguard the faucet in position with the maker given backnut. Once the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The previous kind should be connected to the faucet finishes initially, tightening up just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Installing the Tub
Using the two wooden boards under its feet, put the tub in the required setting. The wood boards are valuable in equally spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four little factors.
The following objective is to guarantee that the tub is leveled all round. This can be accomplished by examining the level and also readjusting the feet on the bathtub until the spirit level reviews degree.
To set up taps, fit the bottom of the outermost versatile faucet adapter to the proper supply pipe by making a compression join; then do the same for the various other faucet.
Turn on the water system as well as check all joints and brand-new pipework for leaks and tighten them if needed. Load the bath tub as well as additionally examine the overflow outlet and also the typical electrical outlet for leaks.
Ultimately, take care of the bathroom paneling as explained in the supplier's instruction manual. Tiling and also sealing around the tub should wait up until the tub has actually been utilized at the very least once as this will settle it into its last placement.
Getting ready for the Installment
Firstly, the sustaining frame supplied with the bath ought to be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to make certain that if the tap comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you use all of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its final placement.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to split a rigid seal, creating the water to permeate the wall surface between the bathroom and the tiling, bring about problems with wetness as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your components as well as fittings. They are offered in tubes and cartridges, and also are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to constantly load the bath tub with water before sealing, to permit the motion experienced when the bathtub remains in use. The sealant can split rather early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a reader about Tools You Need to Install a New Bathtub , I assumed sharing that article was a smart idea. So long as you appreciated our article plz remember to pass it around. Bless you for your time. Come back soon.
Immediate response required?